How to Set Up Bleed Correctly for IngramSpark

A lever paper cutter rests over a purple-bordered printed page marked for trimming.

The blade never lands in exactly the same spot twice. Bleed is the extra color that makes that wobble invisible.

To set up bleed correctly for IngramSpark, add 0.125 inch of bleed on every edge that gets trimmed, cover and interior alike, and make sure it reaches the PDF. Then select bleed for the interior when you set up the title, because a file built exactly right can still come out wrong if that setting is missed.

Bleed is a common reason IngramSpark sends a file back, and fixing the file is only half the job.

My name is Daniel J. Middleton, and after over two decades of editing and designing books for authors and publishers, I still start every project the same way — find out what’s actually broken before touching anything.

This piece covers cover bleed, how I set up interior bleed and margins in InDesign, and the IngramSpark setting that’s easy to miss.

What Is Bleed, and Why Does IngramSpark Require It?

Bleed is extra color or image that runs past the trim line, so the blade never leaves a sliver of white paper at the edge. IngramSpark asks for 0.125 inch (3mm) of it on every edge that gets trimmed.

Anything meant to touch the edge of the page, whether a background color, a photo, or a chapter-opening graphic, has to extend into that extra space. Without it, IngramSpark warns that the printed result can show an uneven white border.

I always run those elements a hair past the 0.125 inch line, not just up to it. Print-on-demand trimming has a small tolerance, so that extra sliver is cheap insurance against a white edge.

How Do You Set Up Bleed on an IngramSpark Cover?

Build the cover as one full spread, back cover, spine, and front cover, with 0.125 inch of bleed on all four outside edges. That adds 0.25 inch to both the spread’s total width and its height.

Always start from IngramSpark’s free cover template generator, which lays this out at your book’s exact trim size and spine width. Working the spread out in your head is a good way to pull your hair out, and the template has already done the math.

Hardcovers work differently: a case laminate cover needs a 0.625 inch wrap instead of 0.125 inch of bleed.

Specs like these change, so check IngramSpark’s Cover File Creation page before you build.

How Do You Set Up Interior Bleed for IngramSpark in InDesign?

I set the page at the book’s trim size and add the bleed with InDesign’s own bleed setting: 0.125 inch on the top, bottom, and outside edge, the three sides that get trimmed. The inside edge gets none, since it disappears into the binding.

The bleed sits outside the page, so a 6 x 9 inch page exports as a 6.125 x 9.25 inch PDF.

That only happens if “Use Document Bleed Settings” is checked under Marks and Bleeds when you export. IngramSpark’s guide to adding bleed in InDesign warns that the bleed is left out of the PDF without it.

How Do You Set Interior Margins for an IngramSpark Book With Bleed?

A small steel ruler measures the margin between a page’s trimmed edge and its text.

With the bleed outside the page, margins measure from the trim line inward. IngramSpark’s minimum is 0.5 inch, but I set the top, bottom, and outside margins at 0.6 inch.

That extra tenth of an inch gives the text a quiet frame, so the eye stays on the words instead of drifting toward the edge of the page.

The inside margin starts at 0.75 inch and grows with page count. A thicker book curves deeper into the spine, so the gutter needs more room to keep the text looking centered as readers turn pages, the same problem behind text that disappears near the gutter.

Which IngramSpark Setup Step Breaks Bleed Even When the File Is Right?

When you set up the title in IngramSpark, you have to select bleed for the interior PDF. That’s a setting in IngramSpark’s own system, separate from the file.

Miss it, and the bleed doesn’t register correctly, even on a file built exactly to spec.

Lightning Source works from the same file specs, since IngramSpark’s own guides are written around a Lightning Source–compliant PDF.

On IngramSpark, bleed only prints right when the PDF and the title setup agree.

What Should You Check Before Submitting Bleed Files to IngramSpark?

Check both parts before you upload, not just one. Open the PDF, go to File > Properties, and confirm the page size includes the bleed, 6.125 x 9.25 inches for a 6 x 9 book. Then confirm bleed is selected in the title setup before you approve anything.

If you’d rather have someone check both before you upload, the get-started page is where to begin.

Daniel J. Middleton

Daniel J. Middleton is the founder of Scribe Freelance, where he designs, edits, and formats books for indie authors, small presses, and publishers — typically starting from a raw manuscript and building the interior layout, cover, and formatting from the ground up. He also diagnoses and fixes production problems in files built elsewhere: a rejected ebook cover, an EPUB formatted by someone else throwing errors in IngramSpark, an interior file that keeps bouncing back. He started in book design in 2007 and has spent close to two decades in the craft.

Next
Next

Why Do IngramSpark Revision Fees Exist (and How Much Are They)?